Bayan

Kɔnɔŋ kënë accepts switch or close switch input from dangerous zone, through safety gate isolation output to safety side relay or transistor output, it has input state detection indication, can perform positive reverse control, the product needs independent power supply, input / output / power three isolation. A lëu bï ya luɔ̈ɔ̈i në NAMUR ye cɔl DIN19234 ye cɔl proximity switches, switches, ku jɔl ya tɛ̈n yenë yen luui në ɣän kɔ̈k yiic (ka tɛ̈n yenë yen luui në tɛ̈n yenë yen luui në tɛ̈n yenë yen

Sertifikatiŋ gël

Numero Sertifikat	GYB081021
Alam anti-explosion	<unk>Exia<unk> IIC (National Level Instrument Instrument Anti-Explosion Safety Supervision Inspection Station Certification)
Parameters of Authentication (Parameters of Authentication)
Terminal	8-7, 11-10
Maximum Voltage ye gam	Um=250V
Voltage	Uo=10.5V
Current ye	Io=16mA
Puwol	Po=42mW
Kapasitɛr	Co=2.4μF
Induktor	Lo=80mH

Kabel diagram

Single input single output wiring diagram

Dual input dual output wiring diagram

Namba Terminal		Terminal bayanna
Daan gël (green)	1	OUT1A（S-）
	2	OUT1B（S+）
	3	OUT2A（S-）
	4	OUT2B（S+）
	5	POW（+）
	6	POW（-）
Daan ye kɛ̈n ye kɛ̈n ye kɛ̈n ye kɛ̈n ye kɛ̈n ye kɛ̈n ye kɛ̈n ye kɛ̈n	7	IN1A
	8	IN1B
	10	IN2A
	11	IN2B

Application 1: Transistor set electrode output Application 2: Transistor emitter pole output

Struktur 外观

EVT1/EVT2: Lamp de luɔɔi: Lamp de luɔɔi ye kɛ̈l ye kɛ̈l ye kɛ̈l ye kɛ̈l ye kɛ̈l ye kɛ̈l ye kɛ̈l ye kɛ̈l Na cï bɛ̈ɛ̈r ye tɔ̈ɔ̈u, a bɛ̈ɛ̈r ye tɔ̈ɔ̈u.

35mm ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye gɛɛr ye.

Lɔ̈k ka tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ̈n tɛ

Parameters teknis

Power
Voltage de luɔi	DC 24V±10%
Power consumption	Single output: ≤0.8W, dual output ≤1.2W
Risky Side
Signal suguya	Contact switch, proximity switch (frequency ≤5KHZ)
Voltage distribution	≈8V (tɛ̈n yenë rot looi)
Short Circuit Radio Waves	≈8mA
Safe Side
Signal suguya output	Relay/transistor
Kapasitet relay output drive	125VAC/0.6A 30VDC/2A
Waktu jaawal relay	＜5ms
Transistor output	Lɔ̈ɔ̈m de electrode ye bɛ̈n looi (tɛ̈n wɛ̈t de wiring ye tɔ̈ɔ̈u në luɔɔi 1): VCC (≤30V), VCC (≤2.5V)
	When emitting pole output (wiring method see application 2): high level VCC-2.5V, low level ≤0.5V
Lɔ̈ɔ̈m ku lɔ̈ɔ̈m (tɛ̈n yenë yen tɔ̈u thïn)
Field switch closed or input circuit current > 2.1mA, output relay or transistor conduction, channel green indicator light
Field switch open circuit or input circuit current <1.2mA, output relay or transistor not conductive, channel red indicator light
Input ku output reverse control settings
Set by panel dial-up switch J5 (tïŋ random instructions)
Kuen insulation
End ye tɔ̈u ku End ye tɔ̈u	2500V，a.c; 1min
Kä ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän ɣän
Temperature ɣän	0～50℃
Humidity	5% ~ 95% RH (ka cɛl)
Standart
Electromagnetic compatibility	A leŋ GB/T18268 Industrial Equipment Application Requirements

Metre sugal

Kë cït: NHR-A35-36/36-K1/K1.
Switch volume input detection end isolation gate, dual input signal is switch volume, dual output is relay contact signal.